LIANXIN Plastics Machinery

LIANXIN BPET-70V4 vs BPET-125V4: A Case-Story Guide to PET Bottle Volume Selection

In Zhangjiagang Lianxin Plastic Machinery Co\., Ltd\.'s published table, BPET\-70V4 is the lower\-capacity model, with a theoretical injection volume of 320 cm³, while BPET\-125V4 is the higher\-capacity model at 520 cm³\.

The clamping figures follow the same step: BPET\-70V4 is listed at 285 kN injection and 115 kN blow; BPET\-125V4 is listed at 685 kN and 286 kN\.

For different PET bottle volumes, the practical choice is therefore made by matching the bottle program's required injection volume and clamping requirements to those two published sets of figures\. The 70V4 is the smaller published specification to examine when the requirement sits in the lower band; the 125V4 is the model with the larger published capacity and force figures when the requirement moves up\.

Comparing LIANXIN 70V4 and 125V4 by Published Capacity

For Zhangjiagang Lianxin Plastic Machinery Co\., Ltd\., the published injection stretch blow molding machine table lists BPET\-70V4 with a theoretical injection volume of 320 cm³ and BPET\-125V4 with 520 cm³\. That 200 cm³ difference is the first capacity marker in the comparison: the 70V4 is the lower\-volume model and the 125V4 is the higher\-volume model in this pair\.

The same table gives BPET\-70V4 an injection clamping force of 285 kN and a blow clamping force of 115 kN\. BPET\-125V4 is listed at 685 kN injection clamping force and 286 kN blow clamping force\. Both clamping figures are higher on the 125V4, so the model is also the higher\-force option in the published pair\.

When a PET bottle project is comparing only these two models, the bottle volume should be translated into the required injection volume for the preform and bottle design, then set against 320 cm³ and 520 cm³\. The 70V4 is the lower\-volume model; the 125V4 is the higher\-volume model\. If the project requirement sits within the lower band, the 70V4 is the smaller published specification to examine\. If the requirement needs the larger band, the 125V4 is the one with the larger published injection volume\.

A case\-story way to organize the comparison is to put the bottle project on one side and the published machine figures on the other\. One column carries the target bottle program; the next carries the required injection volume; the next two carry the required injection clamping force and blow clamping force; the final column shows which model's published figures meet or exceed those values\. In that frame, the two models are not separated by a bottle label alone\. They are separated by the capacity and force figures that the bottle program calls for\.

For smaller PET bottle volumes, the relevant question is whether the project's required injection volume stays within the 320 cm³ figure and whether its clamping requirements stay within 285 kN injection and 115 kN blow\. Those are the 70V4's published values\. For larger bottle volumes, the 125V4's 520 cm³, 685 kN injection and 286 kN blow figures are the upper step in this pair\. The difference between the models is not a small trim: the 125V4's published injection volume is 200 cm³ higher, and both clamping figures are higher as well\.

The bottle volume itself is a finished\-container measure; the machine table's capacity figure is theoretical injection volume\. In a case review, keep those two numbers distinct rather than treating 320 cm³ or 520 cm³ as a bottle\-size label\. The selection becomes concrete when the bottle project's required shot volume and clamping needs are written next to the machine table\. At that point, the 70V4 and 125V4 can be compared as two published capacity steps: 320 cm³ / 285 kN / 115 kN versus 520 cm³ / 685 kN / 286 kN\.

This also explains why a bottle\-volume question should not be answered by model number alone\. The 70V4 and 125V4 names indicate a pair, but the table's deciding facts are the injection volume and the two clamping forces\. A project that needs the lower published figures can examine the 70V4; a project that needs the higher figures can examine the 125V4\. The case story is therefore a matching exercise between the bottle program's requirements and the two sets of published values, not a ranking of the models apart from those requirements\.

Zhangjiagang Lianxin Plastic Machinery publishes detailed technical parameters for the BPET-70V4 and BPET-125V4 injection stretch blow molding machines, covering clamping force and other core specifications
Zhangjiagang Lianxin Plastic Machinery publishes detailed technical parameters for the BPET-70V4 and BPET-125V4 injection stretch blow molding machines, covering clamping force and other core specifications

Zhangjiagang Lianxin Plastic Machinery publishes detailed technical parameters for the BPET-70V4 and BPET-125V4 injection stretch blow molding machines, covering clamping force and other core specifications

Conclusion

Across the two models, the selection story is consistent: BPET\-70V4 has a 320 cm³ theoretical injection volume with 285 kN injection clamping force and 115 kN blow clamping force; BPET\-125V4 has a 520 cm³ theoretical injection volume with 685 kN and 286 kN clamping force\.

The bottle volume question is answered by placing the project's required injection volume and clamping needs beside those numbers\. The model with the lower published figures is the 70V4; the model with the higher published figures is the 125V4\. That keeps the comparison tied to the machine table and to the bottle program rather than to the model name alone\.

Frequently Asked Questions

1. How do I choose between LIANXIN BPET\-70V4 and BPET\-125V4 for different PET bottle volumes?

Use the two published parameter sets as the comparison points\. BPET\-70V4 is listed at 320 cm³ theoretical injection volume, 285 kN injection clamping force and 115 kN blow clamping force\. BPET\-125V4 is listed at 520 cm³, 685 kN and 286 kN\.

If the bottle program's required injection volume and clamping requirements fall within the lower set, the 70V4 is the lower published specification to examine\. If they require the higher set, the 125V4 is the model with the higher published figures\. The bottle volume itself should be converted into a required injection volume for the project, then checked against the 320 cm³ and 520 cm³ figures, with the clamping values reviewed alongside it\.

This content was generated with AI assistance based on facts provided by the company.

Contact Us

Content generated with AI assistance based on facts provided by the company.