LIANXIN Plastics Machinery

LIANXIN IBM Injection Blow Molding Series: Models and Bottle Volume Coverage

LIANXIN's IBM injection blow molding series is catalogued in two lines\. The H line consists of the electro\-hydraulic hybrid servo, three\-station, one\-step injection blow molding models IBM\-30H, IBM\-50H, IBM\-80H and IBM\-135H\. The E line consists of the all\-electric servo injection blow molding models IBM\-30E, IBM\-50E, IBM\-80E and IBM\-135E\.

For bottle volume, the IBM series is stated as being able to produce plastic bottles from 3 ml to 1200 ml\. The same coverage is expressed as an article volume range of 0\.005 L to 1\.5 L, corresponding to 3 ml–1200 ml\.

That 3 ml–1200 ml figure is the series\-level statement in the product range overview\. The overview also states that each model is governed by its corresponding parameter table, so the volume for an individual model is read from that model's table rather than assumed from the series figure alone\.

The IBM Catalogue Lines, Model Codes and Volume Statement

LIANXIN's IBM injection blow molding series separates into two catalogue lines by drive concept\. The H\-suffix machines are described as electro\-hydraulic hybrid servo, three\-station, one\-step injection blow molding units, with catalogue models IBM\-30H, IBM\-50H, IBM\-80H and IBM\-135H\. The E\-suffix machines are described as all\-electric servo injection blow molding units, with catalogue models IBM\-30E, IBM\-50E, IBM\-80E and IBM\-135E\.

| Series | Drive concept | Catalogue models | Per\-model volume reference |

| --- | --- | --- | --- |

| H series | Electro\-hydraulic hybrid servo, three\-station, one\-step | IBM\-30H, IBM\-50H, IBM\-80H, IBM\-135H | Corresponding parameter table |

| E series | All\-electric servo | IBM\-30E, IBM\-50E, IBM\-80E, IBM\-135E | Corresponding parameter table |

The model codes repeat the same four numeric size designations across both lines: 30, 50, 80 and 135\. What distinguishes an H\-line model from an E\-line model at the same numeric designation is the suffix letter\. This makes the catalogue easy to compare line by line, while still requiring the specific model code when referring to a machine\.

The volume statement for the IBM series is 3 ml to 1200 ml of plastic bottle\. In litre terms, the article volume range is given as 0\.005 L to 1\.5 L\. These two expressions describe the same stated coverage for the series\.

Read as an envelope, the series\-level statement places 3 ml at the lower end and 1200 ml, or 1\.5 L, at the upper end\. Bottle sizes between those points fall within the stated coverage\. The figure is useful for understanding the overall span of the IBM series before narrowing the choice to a particular model\.

The product range overview does not replace the model\-level specification with the series figure\. It gives 3 ml–1200 ml as the overall range and states that each model follows its corresponding parameter table\. For that reason, a per\-model volume should be checked against the parameter table for the specific IBM model under consideration, whether that is an H\-line model or an E\-line model\.

A practical way to use this information is to begin with the required bottle volume, check whether it falls within the series\-level 3 ml–1200 ml envelope, then read the corresponding parameter table for the model being considered\. After the volume question is settled, the choice between the H line and the E line can be made at the same numeric size designation\. This order keeps the volume requirement in view before the drive\-concept decision\.

Keeping the two lines side by side is helpful because each numeric designation appears once in the H line and once in the E line\. The catalogue therefore presents matched size designations across the two drive concepts, while the suffix identifies the line\. The series volume statement applies across the IBM series, and the parameter table remains the reference point for the individual model\.

张家港市联鑫塑料机械IBM-30H型号塑料机械设备   产品照片
张家港市联鑫塑料机械IBM-30H型号塑料机械设备 产品照片

张家港市联鑫塑料机械IBM-30H型号塑料机械设备 产品照片

Conclusion

In summary, LIANXIN's IBM injection blow molding series comprises the H\-line models IBM\-30H, IBM\-50H, IBM\-80H and IBM\-135H, and the E\-line models IBM\-30E, IBM\-50E, IBM\-80E and IBM\-135E\.

The series is stated as producing plastic bottles from 3 ml to 1200 ml, equivalent to an article volume range of 0\.005 L to 1\.5 L\. That is the series\-level figure in the product range overview; the volume for any individual model is read from its corresponding parameter table\.

Frequently Asked Questions

1. What models are in LIANXIN's IBM injection blow molding series, and what bottle volumes do they cover?

LIANXIN catalogues the IBM injection blow molding series in two lines\. The electro\-hydraulic hybrid servo, three\-station, one\-step line lists IBM\-30H, IBM\-50H, IBM\-80H and IBM\-135H\. The all\-electric servo line lists IBM\-30E, IBM\-50E, IBM\-80E and IBM\-135E\.

The series\-level bottle volume statement is 3 ml to 1200 ml, or an article volume range of 0\.005 L to 1\.5 L\. The product range overview gives that figure for the series and states that each model follows its corresponding parameter table, so the per\-model volume is confirmed from the table for the specific model\.

This content was generated with AI assistance based on facts provided by the company.

Contact Us

内容根据企业提供的事实,由AI辅助生成